Bowhunters may use a climbing tree stand to travel from one location to another with little effort, allowing them to hunt where the sign is
Bowhunters may use a climbing tree stand to travel from one location to another with little effort, allowing them to hunt where the sign is the freshest. Here are some tips on how to utilise a climbing treestand securely to improve your chances of success.
Climbing Stand Selection
The first thing to consider when utilising a climbing treestand is the location in which it will be utilised. If the terrain is rather simple, a somewhat heavier model might be appropriate.
That same stand, however, will rapidly become a liability if employed in the highlands or other difficult-to-reach regions. As a result, double-check that the stand you choose allows for swift and unobtrusive movement. Weight, size, and “easy of setup” are all important considerations.
Tree Selection
The next step is to choose the correct tree to climb once you’ve picked the right stand. That may seem strange, but when utilising a climbing treestand, the tree picked may have a significant impact on one’s ability to get off the ground and beyond the deer’s line of sight.
Before climbing a tree, the most important thing to consider is its breadth and how much of it it carries upward. To put it another way, a tree that is broad at the bottom and becomes exceedingly narrow as it climbs may cause some difficulties throughout the climbing process and will most likely prohibit you from reaching a suitable hunting height. The best tree is one that does not lose much of its breadth as it grows. Unfortunately, the greatest trees aren’t usually in the finest places, so you’ll probably have to settle for a tree that isn’t in the best form. Knowing how to set up the stand properly at ground level so that it is exactly perfect when hunting height is achieved is crucial when this occurs, and it will.
When choosing a tree to climb, consider the tree’s angle and if it has any branches that you’ll need to cut out of the way on the way up.
How to Get the Best Treestand Position
Let’s begin by imagining the ideal scenario. Finding a tree that is nearly as broad at the bottom as it is at the top is the key. When the stand is installed, the platform must have very minimal “upward” inclination so that it will sit LEVEL after the necessary hunting height is attained.
Remember that the lower the beginning angle must be to adjust for platform drop, the less total tree diameter loss there is.
Let us now consider the worst-case situation. The tree starts out broad at the bottom and narrows as it climbs.
This tree may still be climbed as long as it isn’t too tiny for the treestand’s attachment mechanism to securely bite into it. The key is to tilt the platform UPWARD sufficiently to account for the drop caused by the difference in diameter.
The front of the platform will decrease as the stand travels up the tree as the diameter of the tree varies with height.
By the time a suitable hunting height is attained, it will essentially be pointing down (often too much to properly hunt). When this occurs, the two alternatives are to climb back down and increase the angle of the platform or to choose a different tree. Either method takes time and merely serves to alert deer to the knowledge that they are being targeted. The more you use your climbing stand, the more you’ll get used to the correct angle required to climb any given tree.
Top and Bottom Sections are Secured
After choosing the proper tree and adjusting the platform angle, it’s time to enter the treestand and begin climbing.
However, several safety precautions must be followed before real climbing may begin to guarantee a safe ascent and descent. The first step is to connect the treestand’s top and bottom sections. If the bottom piece of the stand slips from the feet during the ascending process, it will not tumble to the ground.
For this reason, most treestands include a bungee cord or rope attached to both parts. If your climbing stand doesn’t have these stabiliser straps, we suggest getting a pair before climbing any tree.
Keeping Your Feet From Slipping When You’re Standing
Both feet should be attached to the bottom platform, which should be secured to both portions of the climbing treestand to avoid separation during the ascent. In two ways, this will help with the climbing.
For starters, it keeps the feet from sliding away from the stand and causing it to collapse. Second, you must use your feet and legs to lift the bottom half of the treestand UP.
Yes, the top section’s rope will keep it from falling to the ground, but it will still fall as far as the connecting rope will allow. One reason the connecting rope should never be too lengthy is because of this.
This link rope should usually be just long enough for the hunter to make the necessary climbing movements.
Your feet may need to be slid beneath a metal bar or stirrups depending on the brand and type of your tree stand. For specific instructions on where to position your feel when climbing, see the owner’s handbook for your stand.
Keeping Yourself Attached to the Tree
Finally, fasten yourself to the tree before beginning the climbing procedure. If the treestand should break, this will save you from falling. Some bowhunters prefer to tie themselves to the tree once they’ve reached the necessary height, but it’ll be too late if the treestand fails during the ascent.
As a result, the safest method of climbing is to secure oneself to the tree. A complete body safety harness and a safety tether may be used to do this effortlessly. Simply secure your harness while climbing by tethering it to the tree above your head.
You may loosen the tether and move it up the tree as you climb, never detaching from it. Always remember to stay attached to the tree from the moment you leave the ground until you return to the ground at the conclusion of your quest.
For more related articles, please visit: visitpick.com
COMMENTS